24/7 Emergency: 07414 254125
REFCOM · F-Gas Certified
Wall-mounted split air conditioning indoor unit in a commercial office

Split AC

Split AC Maintenance in London & the M25

Split AC Maintenance is handled by engineers who specialise in split air conditioner work. Split systems are simple but fussy about charge and airflow, so pressures and temperatures are measured rather than guessed. Planned maintenance visits follow a written checklist, with readings logged so trends are spotted before they turn into breakdowns. We cover split ac maintenance for homeowners, landlords, managing agents and commercial sites across every London borough and the wider M25. Engineer time is £120+VAT per hour with a one hour minimum, and parts are always quoted in writing before they are fitted.

REFCOM & F-Gas certified24/7 emergency callout£120+VAT/hr · 1 hr minimum

Quick answer

Who provides split ac maintenance in London, and what does it cost?

London HVAC Pro provides split ac maintenance in London and the M25 using F-Gas certified engineers. Engineer time is £120+VAT per hour with a one hour minimum and no call-out fee, parts are quoted in writing before fitting, and same-day attendance is usually available. Call 07414 254125 to book.

More answers: faults and causes, service costs, areas we cover.

Split AC Maintenance explained

Split AC Maintenance is handled by engineers who specialise in split air conditioner work. Split systems are simple but fussy about charge and airflow, so pressures and temperatures are measured rather than guessed. Planned maintenance visits follow a written checklist, with readings logged so trends are spotted before they turn into breakdowns.

  • Refrigerant charge: Interpret readings against operating conditions and equipment specification; do not assume a recharge is the answer.
  • PCB and sensors: Compare the input reading, requested output and actual equipment response; an error code is a starting point, not a diagnosis.
  • Condensate drain: Confirm where condensate should discharge and whether the obstruction, pump or drainage arrangement is responsible.
  • Filters: Filter condition can restrict airflow; cleaning and replacement requirements depend on the filter specification.
  • Remote controller: Compare the input reading, requested output and actual equipment response; an error code is a starting point, not a diagnosis.
  • Interconnecting cable: Confirm the component identity and model-specific requirements before deciding whether adjustment, testing or replacement is appropriate.

Interpreting the reported fault

Compare filters, coil condition, fan response, condensate drainage and controller errors. Poor cooling does not automatically justify a refrigerant recharge.

  • Reported symptom: a split unit blowing warm air
  • Record when the problem started and any recent changes
  • Keep fault codes and model details for the assessment

Maintenance is not a breakdown repair

A planned visit should establish condition and identify deterioration. An existing fault may need separate diagnosis and parts. Agree which assets, cleaning tasks, functional checks and records are included, and base the interval on manufacturer guidance and operating conditions.

  • Provide unit models, fault codes and affected rooms. For ducted systems, include which outlets have poor airflow; for cassettes, note whether water appears below the ceiling.

Labour and the work to be agreed

Engineer time is £120+VAT per hour with a one hour minimum. The time and materials required depend on the diagnosed fault and access. Ask for the repair scope, any additional parts and the return-to-service checks before proceeding.

  • £120+VAT per hour, one hour minimum
  • Confirm the parts and labour required for the specific fault

Split AC Maintenance across London

Comfort cooling needs the correct mode, airflow and heat rejection. A wall split, cassette, ducted system and rooftop unit have different access and drainage arrangements.

An isolated drain, fan or control fault may suit repair. Replacement or new installation needs room load, noise, pipe routes and maintenance access assessed.

Provide unit models, fault codes and affected rooms. For ducted systems, include which outlets have poor airflow; for cassettes, note whether water appears below the ceiling.

Book split ac maintenance in London

Tell us what the system is doing and we will send an engineer with the right parts. £120+VAT per hour, one hour minimum.

Call 07414 254125

Frequently Asked Questions

Engineer labour from £120 + VAT per hour, with a 1-hour minimum. Parts and materials are quoted separately before work begins.

What's included in Split AC Maintenance

  • Condition inspection of each listed asset
  • Cleaning tasks agreed for the equipment type
  • Functional checks of controls and safety devices
  • Readings recorded against the previous visit
  • Written findings, with any repairs quoted separately
  • Refrigerant handling by F-Gas certified engineers, with records kept

How Split AC Maintenance works

  1. 1

    Agree the asset list

    Tell us which units are included and how they are used.

  2. 2

    Set the interval

    Visit frequency is based on manufacturer guidance and operating conditions.

  3. 3

    Planned visit

    The engineer inspects, cleans and tests each listed asset.

  4. 4

    Findings

    Readings and defects are recorded; repairs are quoted separately.

  5. 5

    Follow-up

    Agreed remedial work is booked, and the next visit is scheduled.

Split AC Maintenance prices

ItemPrice
Engineer labour£120 + VAT per hour
Minimum chargeOne hour
Parts and materialsWritten quote before work starts
Planned maintenance contractQuoted per asset list

See all rates on our prices page or read why customers choose us.

Book Split AC Maintenance

Call or book online. Any chargeable work is quoted in writing before it starts.

Split AC Maintenance: scope, checks and next steps

Split AC Maintenance is handled by engineers who specialise in split air conditioner work. Split systems are simple but fussy about charge and airflow, so pressures and temperatures are measured rather than guessed. Planned maintenance visits follow a written checklist, with readings logged so trends are spotted before they turn into breakdowns.

What the reported symptom tells us

a split unit blowing warm air. Record when this occurs, what changed beforehand and whether other equipment is affected. These observations narrow the investigation; they do not prove which part has failed.

Comfort cooling needs the correct mode, airflow and heat rejection. A wall split, cassette, ducted system and rooftop unit have different access and drainage arrangements.

Separate the possible causes

Compare filters, coil condition, fan response, condensate drainage and controller errors. Poor cooling does not automatically justify a refrigerant recharge.

Repair or replacement?

An isolated drain, fan or control fault may suit repair. Replacement or new installation needs room load, noise, pipe routes and maintenance access assessed.

Maintenance is not a breakdown repair

A planned visit should establish condition and identify deterioration. An existing fault may need separate diagnosis and parts. Agree which assets, cleaning tasks, functional checks and records are included, and base the interval on manufacturer guidance and operating conditions.

See the wider equipment service →

What each check helps establish

Refrigerant charge
Interpret readings against operating conditions and equipment specification; do not assume a recharge is the answer.
PCB and sensors
Compare the input reading, requested output and actual equipment response; an error code is a starting point, not a diagnosis.
Condensate drain
Confirm where condensate should discharge and whether the obstruction, pump or drainage arrangement is responsible.
Filters
Filter condition can restrict airflow; cleaning and replacement requirements depend on the filter specification.
Remote controller
Compare the input reading, requested output and actual equipment response; an error code is a starting point, not a diagnosis.
Interconnecting cable
Confirm the component identity and model-specific requirements before deciding whether adjustment, testing or replacement is appropriate.

Details to include with your job request

Provide unit models, fault codes and affected rooms. For ducted systems, include which outlets have poor airflow; for cassettes, note whether water appears below the ceiling.

Before your engineer visits

  • Note the fault code shown on the display.
  • Photograph the rating plate so we can identify the model and refrigerant.
  • Write down when the problem started and whether it is constant or intermittent.
  • Clear access to the indoor unit, condenser or plant area.
  • Move stock out of failing fridges or cold rooms into a working unit if you can.
  • Check the isolator and circuit breaker without opening any electrical panels.
  • Keep previous service sheets and F-Gas leak-check records ready for the engineer.
  • Tell us about roof, ladder, permit or out-of-hours access requirements when you book.
  • Avoid repeatedly resetting equipment, because this can clear useful fault history.
  • Let us know if water, ice or unusual noise is coming from the unit.
  • Confirm who on site can sign off the written quote before extra work starts.
  • Mention any recent building works, power cuts or changes to the room layout.
  • Record the cabinet or room temperature at the start and end of each trading day.
  • Check whether doors, curtains and gaskets close fully and seal.
  • Keep condenser grilles and outdoor units free of boxes, bins and debris.
  • Share the site address, postcode and any loading or parking restrictions.
  • Tell us if the system was installed, moved or serviced within the last year.
  • Note whether neighbouring units on the same system are also affected.
  • Switch off equipment that is leaking water onto electrics, then call us.
  • Ask staff to note any alarms, warning lights or beeping from controllers before the visit.
  • Keep drain lines and condensate pumps visible rather than boxed in behind stock.
  • List every unit you want checked so the engineer can plan time and parts.
  • Tell us if food safety logs show temperatures drifting over several days.